procedures for installing and wiring the SYSDRIVE 3G3FV-j-CUE/EF3HV-j-CUE Please read this manual thoroughly and handle and operate the product with. The SYSDRIVE 3G3FV is OMRON’s new special-purpose inverter. It provides the harmony between performance, versatility, and simplicity. Using a unique. Manuals and User Guides for Omron SYSDRIVE 3G3FV. We have 1 Omron SYSDRIVE 3G3FV manual available for free PDF download: User Manual.

Author: Nikree Vudoktilar
Country: Zimbabwe
Language: English (Spanish)
Genre: Art
Published (Last): 23 August 2009
Pages: 442
PDF File Size: 17.13 Mb
ePub File Size: 8.35 Mb
ISBN: 311-7-49593-196-2
Downloads: 33146
Price: Free* [*Free Regsitration Required]
Uploader: Akijind

Key sequence Display Explanation Displays operation mode. The vibration will be reduced as the integral time I is lengthened. The braking resistor is The deceleration time is too manyal and the regen Refer to the following for the definition of harmonics i.

Operation which uses PID control or other functions. Mode Accessible parameters Operation The Quick-start level parameters can be displayed.

After the basic settings common to all of the control modes are introduced, the basic manuaal tings specific to each control mode will be explained. In control modes with PG, i. If the motor capacity is less than the Inverter capacity the maximum application motor capacityraise the set value. Chapter 8 Maintenance Operations Protective and Diagnostic Functions Fault Detection When the Inverter detects a fault, the fault code is displayed on the Digital Operator, the fault contact output operates, and the Inverter output is shut OFF causing the motor to coast to a stop.

When a magnetic contactor is installed on the primary side of the main circuit to stop a load forcibly, however, the regenerative braking does not work and the load coasts to a stop.

Don’t show me this message again. Otherwise, ventilation will be affected, causing the Inverter to overheat. If a load is connected when auto-tuning is performed, not only will incorrect motor parameters be re- corded, but the motor may operate erratically resulting in dangerous conditions such as loads falling from vertical axis motors. This stored frequency will be retained even after a power interruption and the motor will be restarted at this frequency when a run command is input again.

  CAYLUS INSTRUCTIONS PDF

Set the parameter if stable slip compensation is required in the constant output area where the operating frequency is as high as or higher than the rated frequency. Page Chapter 5 Basic Operation The parameter settings which are used most often are explained below. Terminal Parameter Lists Chapter 4 Trial Operation Procedure 1. Protection Parameter Lists Chapter 6 Advanced Operation Settings The following table shows only those settings related to the torque limit function.

Enter text from picture: Installation and Mounting Install the Inverter according to the installation conditions. Record the current parameter settings as user defaults. Setting Function Inverter power-on time.

Harmonics Harmonic Currents with Voltages Definition Harmonics consist of electric power produced from AC power and alternating at frequencies that are If responsiveness is low, lower the set value. Counts the elapsed time from start-up until power is turned off.

Maintenance And Inspection Page Majual – If the motor rotates even when inverter Chapter 6 Advanced Operation When parameter d the frequency reference hold function selector is set to 1, the held frequency will be stored in memory.

VSG Page 33 – Chapter 2. Replace the cooling fan. In this case, the actual speed limit value is the sum of the voltage input value at terminal 13 and maanual current input value at terminal Page Chapter 5 Basic Operation The multi-function analog outputs have the following functions with these parameter settings.

  AVERY TEMPLATES 8293 PDF

DC braking is mnaual to prevent the motor from rotating due to inertia or external forces when the Inverter is stopped.

Omron SYSDRIVE 3G3FV Manuals

An auto-tuning function allows for easy vector control. Checking The Accessories Stops faster than free-run, without regenerative operation. This output function indicates that zero-servo position control has been completed. Multi-function analog manua 2 terminal These parameters can- not be changed during operation. PID control feedback cannot be set for more than one analog input. Chapter 5 Basic Operation The multi-function analog outputs have the following functions with these parameter settings.

Torque Limit Function Page Chapter 6 Advanced Operation The following diagram shows the relationship between each parameter and the output torque. Alternatively, cables can be routed through a grounded metal pipe to prevent induction noise.

OMRON SYSDRIVE 3G3FV Series Inverters

Warning Labels Warning labels are pasted on the product as shown in the following illustration. Chapter 6 Advanced Operation Electronic Thermal Time Characteristics In this example, L is set to 1 minute, the motor is operating at 60 Hz, and general-purpose motor characteristics are used. Chapter 6 Advanced Operation 33fv Procedure 1. Lengthening the integral 3g3fc lowers the re- sponsiveness, and weakens the resistance to external influences.

General Precautions Make sure that these protective covers are on the product before use.

Standard Connection Diagram The DC reactor is built in.