D External dimensions. D Connections. D Connection of motor. FANUC CONTROL MOTOR AMPLIFIER α series DESCRIPTIONS. B–E. B–E. FANUC AC SPINDLE MOTOR α series PARAMETER MANUAL B– E. FANUC SERVO AMPLIFIER α series DESCRIPTIONS. B–E. FANUC SERVO AMPLIF IER @ series DESCRIPTIONS BE/03 The export of this product is subject to the authorization of the.

Author: Shakarn Gozilkree
Country: Martinique
Language: English (Spanish)
Genre: Business
Published (Last): 14 November 2011
Pages: 148
PDF File Size: 11.81 Mb
ePub File Size: 7.79 Mb
ISBN: 946-6-26805-177-4
Downloads: 82791
Price: Free* [*Free Regsitration Required]
Uploader: Yozshugore

Determine the cross—sectional area of the cables according to Table 5.

Fanuc Servo Amplifier Alpha Series Descriptions E pdf – CNC Manual

When using a built—in motor or a motor with special specifications, refer to relevant specifications, and select a spindle amplifier module accordingly. Otherwise, the cooling efficiency will be reduced so that the characteristics of the amplifier cannot be guaranteed. Check the interface of the CNC being used, and select an appropriate servo amplifier module. The power magnetics cabinet in which the servo amplifier is mounted has 65162f high—voltage section.

Explanation of Spindle Synchronization Control. While the LED is lit, hazardous voltages are present inside the unit, and thus there is a danger of electric shock.

Fanuc B Manuals User Guides – CNC Manual

When transporting them or mounting them in the cabinet, therefore, be careful not to injured yourself or damage the equipment. Select a power supply module according to the capacities of the servo motors and spindle motors being used. F Before connecting the power supply wiring, check the supply voltage.

DI and DO Signals. Motor speed at rapid traverse [min—1] D: In this manual we have tried as much as possible to describe all the various matters. Calculate the CNC input current from the following expression: This acts as the signal ground. Connect the other ground terminal of the terminal block to the frame ground. F Ensure that the power supply lines, power lines, and signal lines are securely connected. Also, keep the specifications at hand.

  ASTM A578 LEVEL B PDF

Some a series servo amplifier modules have batteries in their servo amplifiers. If the input voltage changes, the rated output may not appear even when the input voltage change is within the allowable range. F Do not disassemble the amplifier. In addition, completely seal all cable holes and doors. Note that if some alarms are forcibly reset to enable operation to continue, the amplifier may be damaged.

It contains a fuse. Only a person trained in the maintenance of the corresponding machine or equipment should open the door, and only bb shutting off the power supply to the power magnetics cabinet by opening both the input circuit breaker of the power magnetics cabinet and the factory switch used to supply power to the cabinet.

Fanuc Servo Amplifier Alpha Series Descriptions 65162E

When the rated output capacity is 12 kW or more, calculate according to 3. For dimensions, see Sections 8. When a 665162e is specified, therefore, care is necessary. This amplifier series is designed as a device of installation category overvoltage category II.

Secure that part of the cable to the ground plate by using a clamp. The maximum output data at acceleration is classified into case 1 and case 2. Machine frictional torque motor—converted value [N? Recommended noise filters are listed below. Also, check that no lines are slack.

If the power 651622e reconnected without first replacing the failed component, another 65612e may be damaged, making it difficult to locate the original cause of the alarm. F Never touch the regenerative discharge resistor or radiator directly.

  ANALOG FILTER DESIGN M.E.VAN VALKENBURG PDF

Fanuc B-65162 Manuals

Note that the specification of the coil voltage of a magnetic contactor may differ depending on the supply voltage and frequency used. M6 screw M5 screw?????? The module uses power regeneration that returns energy to the power supply during motor deceleration regeneration.

During operation, all doors must be closed and locked. How to calculate the rotation energy is described in below.

When removing the case or PC board, take care not to lose any screws. To check whether the machine operates as instructed, first specify a small value for the motor, then increase the value gradually. Take appropriate action according to the contents of the alarm.

External Dimensions and Dimensions for Mounting. This carries away the heat generated by the semi— conductors, thus preventing heat from building up in the cabinet as much as possible. F Leave sufficient space around the machine to enable maintenance to be performed easily. For the connector dimensions, see Appendix D. F Before turning on the power, check that the door of the power magnetics cabinet and all other doors are closed.

The machine will not operate normally if a fuse or PC board having other than the correct specification code is mounted, or if a fuse or PC board is mounted in the wrong position. The module uses resistance regeneration that allows energy to be consumed by resistance during motor deceleration regeneration.