Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.

Author: Doujas JoJotilar
Country: Guinea
Language: English (Spanish)
Genre: Technology
Published (Last): 14 December 2016
Pages: 166
PDF File Size: 7.54 Mb
ePub File Size: 7.10 Mb
ISBN: 946-3-15842-542-5
Downloads: 81714
Price: Free* [*Free Regsitration Required]
Uploader: Yolar

Secure the connector cover by hand. As a general rule, wire the Sensor in a separate system, use an independent metal conduit, or use shielded cable. However, if the workpieces are close to the Photoelectric Sensors, light from the adjacent Emitter may be received and cause the Sensor to change to the incident light state.

The lens, however, is plastic.

E3C-VS1G中文资料_图文_百度文库

Typical measures are as given in the following table. Refer to the values omrln the above table to check bend-resistant performance under actual working conditions. Hold the connector cover to connect or disconnect the connector. Close mounting of Sensors is possible by alternating the E3c-vs11g with the Receivers in a zigzag fashion up to two Sensors. If the connector is not connected securely, the connector may be disconnected by vibration or the proper degree of protection of the Sensor may not be maintained.

For bending-resistant cable, see Attachment to Lmron Parts on page C Cable diameter Less than 4 mm 4 mm or greater Tensile strength 30 N max. To maintain the fiber characteristics, make sure that the lock is released before removing the fibers.

  IMAM SAMUDRA AKU MELAWAN TERORIS PDF

Separation from High Voltage Wiring Method Do not lay the cables for the Pmron together with high-voltage lines or power lines. Through-beam Sensors Reflective Sensors 1 If Sensors are mounted in close proximity, use Sensors with the interference prevention function. The following are some examples of applications for which particular attention must be given. Doing so may result in damage from burning and fire, particularly if the liquid is flammable.

Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output

Type of noise Noise intrusion path and countermeasure Before countermeasure Noise enters from the noise source through the frame metal. Lowering the sensitivity will generally help. Insert a capacitor, etc. Precautions for Correct Use Do not use the product in atmospheres 3ec-vs1g environments that exceed product ratings. Do not use pliers, otherwise the connector may be damaged.

Use a soft, dry cloth to clean the Sensor. This information by itself is not suf? Do not use it for such purposes. Be sure to connect or disconnect the connector after turning OFF the Sensor. The axis perpendicular to the center of the lens.

AC 2-wire Sensors Example: If Sensors are mounted in opposite each other, slant the Sensors as shown in the following diagram. The following measures can be taken to avoid mutual interference. Repeated Bending Normally, the Sensor cable should not be bent repeatedly.

  BULA MEROPENEM PDF

Systems, machines, and equipment that could present a risk to life or property. Placing them in the same conduit or duct may cause damage or malfunction due to induction interference.

OMRON Products – Scattergood & Johnson

Precautions for Safe Use To ensure safety, always observe the following precautions. This is because the Sensors may affect each other and cause output chattering even if separated by more than the Sensor sensing distance. Fiber insertion mark Fiber 9mm 2 Removing Fibers Open the protective cover, lift up the lock lever, and pull out the fibers. The axis from the center of the lens to the center of the beam for the Emitter and the axis from the center of the lens to the center of the reception area for the Receiver.

Lens and Case The lens and case of the Photoelectric Sensor are primarily made of plastic. If not grounded, switching noise in the power supply may cause malfunction. They are rather values from samples taken from production lots, and are provided for reference as guidelines.

Typical examples include the minimum sensing object, engineering data, step height detection data, and selection list for specifications.