This tutorial is intended to give basic instruction on how to setup and run a Note: FloXpress will not work if the Flow Simulation add-in is currently installed. Solidworks FloXpress is a feature inside Solidworks that allows a designer simulate flow of fluids through a model. Based on the results of the. This simple tutorial is designed to show you the process of solidworks floxpress. The part that we use here is a simple part because our main goal is the process.

Author: Goltihn Zulkikazahn
Country: Panama
Language: English (Spanish)
Genre: Health and Food
Published (Last): 14 May 2015
Pages: 472
PDF File Size: 20.65 Mb
ePub File Size: 2.10 Mb
ISBN: 196-8-27456-659-6
Downloads: 31242
Price: Free* [*Free Regsitration Required]
Uploader: Gataur

Next we define the inlet boundary conditions.

Tutorial – Using FloXpress in Solidworks?

floxress June 17, by Chris Taylor. Menu Home solidworks tutorial ebooks solidworks 3d sketch-1 solidworks sheetmetal-1 solidworks loft-1 solidworks flowxpress-1 solidworks photoworks-1 solidworks motionstudy solidworks drawing-1 solidworks 3d-sketch-2 solidworks assembly-1 solidworks loft-2 solidworks 3d-sketch-3 solidworks loft-3 solidworks assembly-2 solidworks surface-1 solidworks surface-2 solidworks sheetmetal-2 solidworks assembly-3 solidworks simulation-1 solidworks advanced loft solidworks drawing 2 solidworks toolbox solidworks pattern solidworks surface 3 solidworks simulation 2 solidworks helix.

Solidworks FloXpress is a feature inside Solidworks that floxoress a designer simulate flow of fluids through a model.

Next we choose the fluid that would flow through the model. This simple tutorial is designed to show you the process of solidworks floxpress. All of these articles will be stored in the category of Daily Doseā€¦. A sample report is like the one shown below.

  DISCRASIAS SANGUINEAS PDF

SOLIDWORKS Free Xpress Utilities-Part 4-FloXpress

Close the check geometry window. From the results window you can simulate the trajectory of fluid particles as they move through the model. The opening must be closed with lids.

Now go for the floxpress on the tools menu again. Define a plane parallel to the end face of the part and set the mm offset distance. You can examine the flow in much more complicated parts floxpess valves too the process is the same.

Now the part is ready. A new assembly opens, the begin assembly window appears with your part ready to insert, just click on the working area and your part will insert there.

SOLIDWORKS Free Xpress Utilities-Part 4-FloXpress – Computer Aided Technology

Once a pressure is selected, you can run the analysis to calculate flow velocity. Once the geometry is valid, you next select water or air as the fluid for the tutkrial. We need to first create the lids for the two ends before we begin the simulation. Click next and then click solve and wait. Use this information in conjunction with experimental data and practical experience. As you can see in the message box, the model is not ready for flow analysis. The velocity chart illustrates the flow speed during the processthe colors are observable in the flow.

Share this with your friends. This is a great tool to tuorial you identify problem areas in your design and improve them before you manufacture tutroial parts. Home solidworks tutorial ebooks solidworks 3d sketch-1 solidworks sheetmetal-1 solidworks loft-1 solidworks flowxpress-1 solidworks photoworks-1 solidworks motionstudy solidworks drawing Based on the results of the simulation the designer.

  EL POZO BALDOMERO LILLO PDF

The Solidworks FloXpress icon is located under the evaluate tab.

Trajectories are tangent to the flow velocity at every point. So right click on main part and select appearance. Now there is a lid on one side. SWA home about contact us. First you must model the following part and I assume that you know the basics of solidworks 3d modeling. Click on the next button again. Floxppress will make sure that my future students have the links to read this themselves. I went with a C-D Nozzle geometry for this demonstration. Once we have created the lids we foxpress then proceed to begin the simulation.

You can also choose to generate a report from the FloXpress simulation by simply clicking on the generate report icon at the bottom of the results tab.

This free tool allows you to calculate how fluid or air flows through a part or assembly document.